There are many types of kites: boxy, square, Dragon pictures, pictures of birds, pictures of people. ... But to fly high and solid is the kite crows. So you ask yourself to make yourself a kite shaped crows are best, and invite you to please consult how to do below:First you have to make bamboo wing frame. Maybe you should bịhai the bamboo stick length 90 cm, the medium. You are forced to stick a bamboo on the other end, is the bar under the stars for real thang by two wings. This bamboo stick you should to about 22, the beautiful 23cm. But that's not enough, you must make two curved wings side up by forcing the two head into the bar's axis in the middle (midpoint of shaft on the bar). But the first singles have to bend too splintered to miss. Often the two wings will not curve are circular and curved gather in one spot, as well. So did you get the wings of the Raven paper. Next is the head and tail are very simple:First: You prepare two small bamboo, short of about 9-10 cm, forced into suicide the shaft then forced on the other end into the spearhead.Tail: also the two bamboo stick but longer, about 20-30 cm, forced into triangles. But a sharp head of the triangle is fastened with the axis (in about 1/3 the shaft), sharp-angle of about 70 degrees, the medium. When all frames then you paste the new paper. If the small paper, you must paste each piece of the wing and are sealed. The paper was covered up by a sticky paws, kite lines, scissors for flat edge then paste on the bamboo stick around. The head and tail are similar.Finally is the Clinch (Democrat). You have to carve two small holes on the bamboo bar on surveillance of paper wings (two small holes between the weight axis, from the axis to a hole about 10-15 cm), tying the two ends of the rope about 3 cm into the two holes we are part of the Democrat. Next take a piece of wire about 30 cm piece of wire on the front, the other end tied to his love of tail shaft. And the wire connected to the coil will tie into the second paragraph, he forced the truth sure but still move was on the line Monday for tune. The main part of this range from 3-5 cm (on the second line from the first line). So, you already have a paper. There are many types of kites: boxy, square, Dragon pictures, pictures of birds, pictures of people. ... But to fly high and solid is the kite crows. So you ask yourself to make yourself a kite shaped crows are best, and invite you to please consult how to do below:First you have to make bamboo wing frame. Maybe you should bịhai the bamboo stick length 90 cm, the medium. You are forced to stick a bamboo on the other end, is the bar under the stars for real thang by two wings. This bamboo stick you should to about 22, the beautiful 23cm. But that's not enough, you must make two curved wings side up by forcing the two head into the bar's axis in the middle (midpoint of shaft on the bar). But the first singles have to bend too splintered to miss. Often the two wings will not curve are circular and curved gather in one spot, as well. So did you get the wings of the Raven paper. Next is the head and tail are very simple:First: You prepare two small bamboo, short of about 9-10 cm, forced into suicide the shaft then forced on the other end into the spearhead.Tail: also the two bamboo stick but longer, about 20-30 cm, forced into triangles. But a sharp head of the triangle is fastened with the axis (in about 1/3 the shaft), sharp-angle of about 70 degrees, the medium. When all frames then you paste the new paper. If the small paper, you must paste each piece of the wing and are sealed. The paper was covered up by a sticky paws, kite lines, scissors for flat edge then paste on the bamboo stick around. The head and tail are similar.Finally is the Clinch (Democrat). You have to carve two small holes on the bamboo bar on surveillance of paper wings (two small holes between the weight axis, from the axis to a hole about 10-15 cm), tying the two ends of the rope about 3 cm into the two holes we are part of the Democrat. Next take
đang được dịch, vui lòng đợi..