Quy trình kéo, rải cáp, và đấu nối

Quy trình kéo, rải cáp, và đấu nối cápMột số quy định chung:- Đối với hệ thống báo cháy, có các loại cáp chính là cáp 2x1,5mm2, cáp 2x0.75mm2 chống cháy, chống nhiễu. Khi thực hiện kéo cáp, cần chú ý những điểm sau: Sức kéo căng.  Bảo vệ cáp khi kéo. + Bán kính đường cong:- Hầu hết các loại cáp này được thiết kế mềm dẻo, rất rễ lắp đặt. Tuy nhiên, không phải là ta có thể kéo dài đoạn cáp hay uốn cáp theo độ cong tuỳ thích mà phải tuân thủ theo một dải nhất định và một độ cong hợp lý cho phép.+ Bảo vệ cáp khi kéo:- Trong quá trình kéo cáp, ngoài việc tuân thủ sức kéo căng và độ uốn cong của cáp, ta phải tránh việc cáp tiếp xúc với các vật dụng gây hỏng cáp ở xung quanh.- Ví dụ: Ta không kéo cáp qua chỗ có bề mặt sắc nhọn, góc cạnh kim loại vì nó có thể làm hỏng vỏ cáp và xấu nhất là làm đứt dây cáp.Lắp đặt dây tín hiệu, trên trần, trên vách bê tông- Việc đi ống ghen sắt được lắp sát vào trần, dầm bê tông được thực hiện trước.- Kéo rải dây trong ống ghen và để chờ tại các hộp nối các thiết bị.- Dây không được căng quá dẫn đến dễ đứt.- Tại vị trí nối để thừa từ 20÷30 cm để sau này cắt nối.- Việc đi dây đến đâu phải vẽ lại, hoàn công đến đó. Nếu có phần ngầm cần phải mời Chủ đầu tư nghiệm thu trước khi lấp kín.- Khi bắt đinh ghim ống luồn dây lên trần, dầm thì không được ghim bừa bãi mà phải ghim vào đúng vị trí mà đã được xác định từ trước và đã đươc đồng ý từ TƯ VẤN GIÁM SÁT.

Kết quả (Anh) 1:

Process of pulling, spreading cables, and connecting cables Some general regulations: - For fire alarm systems, the main types of cables are 2x1.5mm2 cable, 2x0.75mm2 fireproof, anti-interference cable. When performing cable pulling, pay attention to the following points:  Tensile strength.  Protect the cable when pulling. + Curve radius: - Most of these cables are designed to be flexible and very easy to install. However, it is not possible to lengthen the cable or bend the cable to the desired curvature, but must comply with a certain range and a reasonable allowable curvature. + Protect the cable when pulling: - During the process of pulling the cable, in addition to complying with the tension and bending of the cable, we must avoid the cable coming into contact with objects that cause damage to the cable around. - For example: We do not pull the cable through places with sharp surfaces or metal edges because it can damage the cable cover and worst of all, break the cable. Installing signal wires, on the ceiling, on concrete walls - The installation of iron pipes installed close to the ceiling and concrete beams is done first. - Pull the wires in the duct and wait at the equipment connection boxes. - The string must not be too tight as it can easily break. - At the joint position, leave 20 ÷ 30 cm extra for later cutting. - Wherever the wiring goes, you have to redraw it until it's completed. If there is an underground part, it is necessary to invite the Investor to accept it before filling it. - When pinning conduit to ceilings or beams, do not pin indiscriminately but must pin to the correct location that has been determined in advance and has been agreed upon by the SUPERVISION CONSULTANT.

Kết quả (Anh) 2:

Procedure for pulling, laying, and connecting cables
Some general rules:
-For fire alarm systems, the main cable types are 2x1.5mm2 cables, 2x0.75mm2 flame retardant, and anti-interference cables. When pulling the cable, the following points should be noted:
Tensile strength.
Protect cables during traction.
+Curve radius:
-Most of these cables are designed for flexibility and are installed at the very base. However, this does not mean that you can extend the cable or bend it to the desired degree, but rather that you must adhere to a certain range and a reasonable degree of bending.
Cable protection during traction:
-During the cable pulling process, in addition to complying with the stretching and bending of the cable, it is also necessary to avoid contact between the cable and surrounding objects that damage the cable.
For example, do not drag cables over areas with sharp surfaces and metal edges, as this may damage the cable casing and in the worst case, the cable.
Signal lines installed on ceilings and concrete walls
-The iron envy tube is installed on the ceiling, and the concrete beam is completed first.
-Put the rope in the jealousy tube and wait at point H

Kết quả (Anh) 3:

The process of pulling, laying and connecting cables
Some general rules:
-For fire alarm systems, the main types of cables are 2x1.5mm2 cables and 2x0 cables. 75mm 2 fire prevention and interference prevention. Pay attention to the following points when pulling cables:
Nervous pressure.
Protect the cable when pulling.
+Curve radius:
-Most of these types of cables are flexible in design and very rooted in installation. However, we can't extend or bend the cable section to any degree, but we must abide by a certain range and reasonable allowable degree.
+Protect the cable when pulling:
In the process of cable pulling, in addition to observing the tension and curvature of the cable, it is also necessary to avoid contact between the cable and the surrounding objects that damage the cable.
-For example, we won't pull the cable over sharp surfaces and metal corners, because it will damage the cable shell and, worst of all, cut the cable.
Put the signal wire on the ceiling and on the concrete wall.
-The operation of the gooseberry pipe is installed on the ceiling, and the concrete beam is carried out first.
-Stay in the jealous tube and wait in the connection box for the equipment.
The rope should not be too tight, it will break easily.
-Extra 20 ÷ 30cm at the connection position, so as to cut off the connection later.
-The job of the rope is not to repaint, but to get there again. If there are potential parts, investors must be invited to make acquisitions before filling them.
-When nailing the conduit to the ceiling, the conduit shall not be nailed at will, but must be nailed in the correct position determined in advance and approved by the Wire Control Regulations.