- Gá khuôn lên máy ép: Sau khi lắp 

- Gá khuôn lên máy ép: Sau khi lắp hoàn chỉnh bộ khuôn, lắp bu lông vòng vào khuôn, sử dụng pa lăng để cẩu khuôn lên máy ép. Canh cho bạc cuống phun vừa khít với đầu vòi phun. Cho máy ép ép vào. Sau đó, tháo bu lông vòng ra. Sử dụng đồ gá gá chặt bộ khuôn trên máy.
- Bắt hệ thống đường nước cho khuôn: Sau khi gá khuôn lên máy, điều khiển máy tách 2 lòng khuôn ra để dễ dàng trong việc lắp ráp đường nước. Lần lượt lắp bu lông đường nước vào. Nên quấn băng keo non và bôi keo chống thấm để khi ép nước không bị rỉ. Sau đó, gắn ống nước vào và siết chặt bằng cổ dê.
- Lắp các bộ phận phụ trợ: Lắp các bộ phận phụ trợ (nếu có) lên khuôn như: Bộ điều khiển hearter hay bộ gia nhiệt nước, cảm biến,…
- Chuẩn bị vật liệu nhựa: Việc chuẩn bị vật liệu nhựa đã được tính toán trước thông qua CAM, CAE, yêu cầu của người đặt hàng hay tính chất của sản phẩm,… Bỏ nhựa vào thùng chứa trên máy, sau đó bật công tắc cho máy sấy khô hạt nhựa.
– Kiểm tra đường nước: Bật hệ thống đường nước cho nước chảy qua khuôn. Nếu nước rỉ ra thì cho dừng lại và khắc phục chỗ rỉ nước đến khi nào nước hết rỉ là đạt yêu cầu.
- Ép thử: Sau khi đã chuẩn bị mọi thứ đạt yêu cầu, bước kế tiếp là ép thử xem máy ép hoạt động tốt không. Ép 2 lòng khuôn lại với nhau phun nhựa vào đợi 15s, lấy sản phẩm ra và kiểm tra xem sản phẩm có đạt yêu cầu không.
- Thiết lập lại các thông số ép: Sau khi ép thử, nếu sản phẩm chưa đạt yêu cầu do thông số ép, tiến
hành thiết lập lại các thông số ép cho phù hợp thông qua quá trình mô phỏng CAE và CAM đã tính toán. Sau đó, thực hiện ép lại để kiểm tra sản phẩm dựa vào các yêu cầu của nhà sản xuất và các yêu cầu kỹ thuật của bản vẽ trong quá trình CAD.
- Thay đổi thông số của các bộ phận phụ trợ để đạt được yêu cầu
của khách hàng.
- Tổng kiểm tra sản phẩm lần cuối cùng, nếu sản phẩm đã đạt yêu cầu thì giao hàng, nếu không đạt yêu cầu thì thực hiên thiết kế lại sản phẩm.

Kết quả (Anh) 1:

-Holders of the mold up presses: after fitting the complete mold, insert the bolts into the ring mold, using pa lang to mold the crane onto the presses. The broth for the silver spray stem fits with the nozzle head. For injection molding presses on. Then, remove the bolts round out. Use brackets to fasten the jig jig on the air.-Water line system for mould: mould onto your set-up, after driver spun 2 egg mould to ease in the Assembly lines. Turn the mounting bolts on the water line. Should wrap the adhesive and waterproof glue applicator to not leak water when pressed. Then, attach hose on and squeeze by goat stock.-Insert the auxiliary parts: Mounting the auxiliary parts (if any) onto the mold, such as controllers for heat or water hearter, sensors, ...-Preparation of plastic materials: the preparation of plastic material was calculated via the CAM, CAE, required by the order or nature of the product, ... Remove the plastic into containers on air, then switch for air dried plastics.-Check the water line: Turn the water system for water flow through the mold. If the water leak out to stop and fix possible leak water leak out until water is satisfactory.-Pressed to try: after having prepared everything satisfactory, the next step is to try molding presses works well no. Juice 2 egg mold together plastic-spray on wait 15s, getting the product out and check that the product is not satisfactory.-Reset the Following presses: when pressed to try, if the product is not satisfactory due to the parameters, proceedreset the Administration pressed for matching through CAE simulation process and CAM have calculated. Then, make pressed again to check the products based on the request of the manufacturer and the technical requirements of the drawing in the CAD process.-Change parameters of auxiliary parts required to achieveof the customer.-Total final product testing, if the product has reached the required delivery, if not satisfactory then initiated a redesign of the product.

Kết quả (Anh) 2:

- Holder molding presses up: After installation is completed the mold, the mold mounting bolts on the ring, used for hoisting winch, presses the mold up. Align the stem silver spray nozzle fit. For molding presses on. Then, remove the ring bolts. Using cutting jig fixtures on the site.
- Getting water line system for mold: After boarding jig mold, machine control 2 separate cavity to ease the assembly line in the country. Turn mounting bolts on the water line. Young should wrap duct tape and glue waterproof to water does not leak when pressed. Then, attach the water hose and tighten with old goat.
- Installation of auxiliary parts: Installation of auxiliary parts (if any) on the site such as controller Hearter or water heaters, sensors, ...
- preparation of plastic material: the preparation of plastic materials have been calculated in advance through CAM, CAE, requirements of the order or nature of the product, ... plastic put into containers on the machine, then turn on the rules for plastic resin dryer.
- Check the water line: Turn the water line system for water flowing through the mold. If water leaks out, then to stop and fix the leak site until the end of dripping water is satisfactory.
- Injection test: After having prepared everything satisfactory, the next step is to try pressing operation presses well not. 2 pressed together cavity plastic injection to wait 15s, taking the product out and check whether the product is satisfactory.
- Reset All molding: After pressing test, if the unsatisfactory by molding parameters, process
operating parameters reset accordingly pressed through CAE and CAM simulation calculated. Then, perform forced back to test the product based on the requirements of the manufacturer and the technical requirements of CAD drawings in the process.
- Change the parameters of auxiliary parts to achieve love needs
of the customer.
- General check last product, if the product has to meet requirements, delivery, if unsatisfactory, perform redesign products.