FEATURES OPERATION OF PANEL CGC413 The operating parameters of the machine is continuously updated and displayed on the screen of the electronic digital control panel. 1 to 9 Keys Keyboard screen closed mesh screen 2 Keys Key figure breaks down to 10 mesh 3 Keys confirm installation, fault, ... 11 Keys plays generator 4 key return interrupt generator 12 Keys 5 Keys to run manual mode MAN 13 keys manually started the engine key 6 check LED full screen 14 films to be stopped manually 7 Keys to run automatic mode AUTO 15 Reset button error test run TEST key 8 Display voltage AC (volage V) voltage generated is displayed on the screen the norm is the standard voltage of 400 / 230V, and voltage fluctuation of 1%. This parameter when the ignition key is on, press select on the display until this parameter appearing Show power consumption (power VA) When a consumer load, depending on electricity consumption but on screen form continuous updates easy for users to know and regulate power consumption so that reasonable. See this parameter when the ignition key is turned on, press select on the display until this parameter appears. Displays frequency (freguency Hz) frequency alternating current generated is displayed on the screen typically 50Hz with frequency variation is 1%. This parameter when the ignition key is turned on, press select on the display until this parameter appears. Displays rotation speed (RPM) Speed of motor rotation is displayed on the screen at a rate the norms of 1500 rev / min see this message when the ignition is on, press select on the display until this parameter appear Display the engine temperature parameter for engine temperature, see this parameter when the ignition key is turned on, press select on the display until this parameter appear Display battery voltage (Vdc) parameter is displayed on the 1-dimensional voltage VDC. See this parameter when the ignition key is turned on, press select on the display until this parameter appear Display machine runtime (Runtime h) This parameter is the total time of breath running machine, thereby Know maintenance cycle generator. See this parameter when the ignition key is turned on, press select on display until parameters appear. Notice the fault protection system lubricant pressure warning light will light up and the screen will display the error when pressure engine lubricating oil is lower or higher than the standard value. The cause of the incident is a lubricant is missing, damaged two oil pump or oil filter clogged. When this error protection system Emergency stop and the engine will automatically stop. Frequency indicator lights up and the screen will display the error frequency emitted exceeded the standard value. The cause may be due to overloading. When this error protection system Emergency stop going to work and stop the engine itself. Please adjust load used, if the frequency is too low, some devices will not consume work. When high too damaged equipment. Ø Ø Voltage This parameter is usually the default display screen is always on when the machine starts running. If the voltage emitted exceeds the standard value of 400 / 230V with the knife up 1%, the alarm lamp will light up and the screen will display the error. Caused by overloading. When this error protection system Emergency stop working and the engine will automatically stop. overload indicator will light up and the screen will display the error when power consumption exceeds the capacity market norms of the machine, the machine will be overloaded. When this error protection system emergency and automatic engine stop. No boot machine warning light will light up and the screen will display the error when the engine would not start. The cause may be due to low battery voltage, battery solution in short supply, fuel supply system off or with e ... fuel. When experiencing this problem follow the manual to fix or contact the supplier. Emergency Stop Accident synthesis machine will automatically stop or when the user presses the emergency stop button, at This indicator will light up and the screen will display an error indicating that the machine has to be protected. Want to turn off the computer using the ignition key on and on. voltage battery charging indicator will light and the display will show an error in operation of the machine that the battery is not charging. The bug lies in the generator charging system for the battery, this error does not automatically stop the machine. Not to operate in this state so long the battery will power consumed several times. When this error occurs, please contact your supplier. Machine overheating indicator lights up and the screen will display the error when the coolant temperature rose too high. Caused by the lack of water. Incident synthesis If generator is overloaded or malfunctioning motor, general alarm light will light up and the machine stops operating. Check the cause of the incident. When the alarm lights lit synthetic and motor stopped, must: + OFF automat output load + Restart the engine + Please read the voltage number on the screen *) If the voltage is normal, check the input device circuits in the state of default or not. If the system is normal, contact your supplier. *) Malfunctions in the charging system: When the malfunction in the charging system warning light will light up and the screen will display the error that was made engine with power from the battery. Installation and foot fighting back: 3.2 Operating procedures generators
đang được dịch, vui lòng đợi..
